Troy Bilt Easy Start String Trimmer Parts Diagram

Accessories

Accessories for the Troy-Bilt TB575EC

Questions & Answers

---

How do I take the spool head off to replace it?

Nancy for model number TB575EC asked on 2019-06-27

Hello Nancy, thank you for your inquiry. There is a video listed directly under the cutting head assembly on how to replace this part. Thank you. https://www.ereplacementparts.com/cutting-head-assembly-p-571393.html

Did this question help you?

No compression. What do I need to fix this problem?

Kelly McGregor for model number TB575EC asked on 2019-07-11

Hello Kelly, thank you for your question. The lack of compression is a problem generally caused by air leaks. Leaks can occur along the crankcase, the piston seals or the intake manifold. We would recommend checking these areas and then replacing any gaskets, seals, or o rings that are leaking. I hope this helps!

Did this question help you?

Wherecan I get accessories like a saw bade and connectors for this trimmer

John for model number TB575EC Gas trimmerW asked on 2019-08-11

Hello John and thank you for writing The cutting head assembly Part # 753-08182 is in the list of compatible items for your model. Hope this helps Could you please clarify which connectors you are after ?

Did this question help you?

The cutting head does not rotates fist it slow

Russell for model number TB575EC asked on 2019-10-09

Hello Russell, thank you for your inquiry. Attached is a link that will help you with your question. Thank you. https://www.fix.com/repair/lawn-and-garden/trimmer/engine-revs-but-trimmer-head-will-not-turn/

Did this question help you?

This may be a dumb question, but how can I restring my trimmer? Do I need to get a new head assembly or can I just restring the one I have?

Steve for model number Model tb575ec 4-cycle trimmer asked on 2021-08-08

Hello Steve, Thank you for your inquiry. We show the cutting head assembly for your model as part# 753-08182. As per Troy Bilt, you should be able to restring the head. We have included a link to the owners manual for your model to give you instructions on how to restring the head. Hope this helps. https://www.manualslib.com/manual/836022/Troy-Bilt-Tb575-Ec.html?page=8#manual

Did this question help you?

Discussion

Discussion for the

Discussion is closed. To ask our experts a question about a part, use the Q&A feature on our product pages.

I can't find the fuel bulb that you pump in your parts list. Can you help?

Hello rpss Here it is on another site:

link removed

Here it is on this site:

http://www.ereplacementparts.com/walbro-primerbulb-p-402858.html

Question: TB 575 Ignition Coil

dertel

Is there any way to check the ignition coil?
I'm getting no spark.

Hello dertel They say there is using an ohm meter or multimeter...Set Ohms setting on it to 20K. Touch one lead to spark plug lead inside the boot, touch the other lead to one of the coil legs. A zero or Infinity reading may indicate a bad coil. A reading of 2.5K to 5.0K indicates a good coil. If you get a reading of ONE, move the Ohm setting down one.
Make sure you have the proper air gap between the coil legs and the magnets in the flywheel. Should be about .010" About the thickness of a business card. Use one for a gauge.

Question: Adjusting Valves

scoon

need to know the gap setting on the valves

scoon A lash of .004" to .005" will work fine.

Question: Line Wont Advance

chub

When tapped on ground line does not advance

Hello chub,

If the 753-04236 upper drive shaft and the 753-05267 lower drive shaft are rotating correctly and so is spindle end on the 753-06124 gearbox assembly. I would think that there is a problem with the 753-06129 cutting head and spool assembly not allowing the line to advance.

-WJA

woodplarriving1938.blogspot.com

Source: https://www.ereplacementparts.com/troybilt-tb575ec-41edt57c966-gas-string-trimmer-parts-c-26780_27267_202396.html

Share this post